進口高壓蝶閥德國洛克廠家直銷

一、進口高壓蝶閥技術參數：

1、連接方式：對夾、法蘭、對焊

2、尺寸（mm）:DN40-1000

3、適用溫度（攝氏度）：-40℃~+600℃

4、壓力范圍（MPa）:0.6-50MPA

5、閥體材質：A216 WCC A351 CF8M BS1400 AB2

6、閥板材質：CF8MENP BS1400 AB2

7、閥桿材質：17-4PH、K-Monel

8、閥座材質：增強型聚四氟乙烯RTEF、UHMPE、PEEK、Inconel

1. Connection mode: wafer, flange, butt welding

2、 Size (mm): DN40-1000

3. Applicable temperature (Celsius): - 40 ℃ ~ + 600 ℃

4. Pressure range (MPA): 0.6-50mpa

5. Valve body material: A216 WCC a351 CF8M bs1400ab2

6. Valve plate material: cf8menp bs1400ab2

7. Stem material: 17-4PH, k-monel

8. Seat material: reinforced Teflon rtef, UHMPE, peek, Inconel

二、進口高壓蝶閥主要應用：

化工、石化、冶煉、醫藥、食品等行業中SO2、蒸汽、空氣、煤氣、氨氣、CO2氣、油品、水、鹽水、堿液、海水等介質的管路上作為調節和截流裝置使用

In chemical, petrochemical, smelting, pharmaceutical, food and other industries, SO2, steam, air, gas, ammonia, CO2 gas, oil, water, salt water, alkali liquor, sea water and other medium pipelines are used as regulating and intercepting devices

三、進口高壓蝶閥產品特點:

一、閥桿防吹出環

防止閥桿在意外情況下被吹出

可更換的閥板密封環     

降低現場維護成本

二、動負載填料壓蓋  

標準低排放閥桿密封，泄漏率為百萬分之0-20

動負載具有可預測及不變的填料壓縮力，可持續使用5000個開關循環操作，而不需要調整或重新填料。

廷長了填料使用壽命

三、可帶壓更換填料的設計

可以在不降低管道壓力的情況下,并在閥門開閉任意角度進行更換或補充填料.降低現場維護成本

全金屬密封系統     

高硬度、抗沖刷、耐磨、耐高溫

濾網式閥桿軸承系統      

降低閥門扭矩

T

四、閥板位置顯示            

閥桿末端提供簡單的閥位指示

1、 Stem blow out ring

Prevent the stem from being blown out accidentally

Replaceable valve plate seal ring

Reduce site maintenance costs

2、 Dynamic load gland

Standard low discharge stem seal, leakage rate 0-20 ppm

The dynamic load has predictable and constant packing compression force, and can be operated continuously with 5000 switching cycles without adjustment or refilling.

Long service life of packing

3、 Design of replaceable packing under pressure

The packing can be replaced or replenished at any angle of valve opening and closing without reducing the pipeline pressure, so as to reduce the field maintenance cost

All metal sealing system

High hardness, erosion resistance, wear resistance and high temperature resistance

Screen type stem bearing system

Reduce valve torque

4、 Valve plate position display

Simple valve position indication at the end of stem

四、進口高壓蝶閥產品簡介：

德國《LOCKE》洛克進口高壓蝶閥(High pressure valve)適用范圍已可以耐壓高達 2500 磅級，耐溫低至 -196 ℃高達 700 ℃，密封達到 0 泄漏，調控比高達 100:1 以上。也就是說在各種嚴酷、關鍵的過程控制管線上，不論是開關閥還是調控閥，只要選型得當，現在都可以放心地使用蝶閥，而且成本低廉。進口超高壓蝶閥閥芯采用三偏心金屬硬密封蝶閥實現雙向密封，能正、反雙向承壓，正或反向承壓時均不發生內漏。

The high pressure valve imported from Locke, Germany, can withstand pressure up to 2500 pounds, with temperature resistance as low as - 196 ℃ and as high as 700 ℃, sealing up to zero leakage and control ratio as high as 100:1. That is to say, in all kinds of severe and critical process control pipelines, no matter on-off valve or control valve, as long as the selection is proper, butterfly valve can be safely used now, and the cost is low. The imported ultra-high pressure butterfly valve adopts the three eccentric metal hard sealing butterfly valve to achieve two-way sealing, which can bear pressure in both positive and negative directions, and no internal leakage occurs when bearing pressure in both positive and negative directions.