德國洛克進口乙炔鋼瓶減壓閥型號齊全安全可靠

一、進口乙炔鋼瓶減壓閥規格參數：

最大輸入壓力：3000，500 psig

輸出壓力：0～25，0～50，0～100， 0～250 psig

安全測試壓力：1.5倍的最大輸入壓力

適用溫度：-40°F 至＋165°F（-40℃至＋74℃）

Maximum input pressure: 3000500 PSI

Output pressure: 0-25, 0-50, 0-100, 0-250 psi

Safety test pressure: 1.5 times of the maximum input pressure

Applicable temperature: - 40 ° f to + 165 ° f (- 40 ℃ to + 74 ℃)

二、進口乙炔鋼瓶減壓閥設計特點：

● 活塞式減壓結構 ● 母體螺紋：1/4" NPT（F） ● 內設過濾網 ● 可采用面板式或墻式安裝

■ 適用范圍

● 實驗室 ● 氣體分析測試 ● 流程控制 ● 氣體匯流排 ● 測試設備

■ 特性參數

● 最大輸入壓力： 3000，6000psig   ● 輸出壓力：0~250,0~500,0~1500,0~3000psig

● 安全測試壓力：1.5倍的最大進氣壓力 ● 適用溫度：-10℉~+165℉(-23℃~+74℃)

● 泄漏率：泡沫測試 ● CV值：0.06 ● 重量：0.9kg

材質：

◆母體：316L，Brass

◆上蓋：316L，Brass

◆膜片：316L

◆過濾網：316L（10μm）

◆閥座：PCTFE，PTFE，Vespel

◆彈簧：316L

◆閥芯頂桿：316L

Piston type pressure reducing structure ● mother thread: 1 / 4 "NPT (f) ● filter screen inside ● can be installed in panel or wall

■ scope of application

● laboratory ● gas analysis and test ● process control ● gas bus ● test equipment

Characteristic parameters

Maximum input pressure: 30006000 psi ● output pressure: 0 ~ 250,0 ~ 500,0 ~ 1500,0 ~ 3000psi

Safety test pressure: 1.5 times of maximum inlet pressure ● applicable temperature: - 10 ℃～ 165 ℃ (- 23 ℃ ~ + 74 ℃)

Leakage rate: foam test > CV: 0.06: weight: 0.9kg

texture of material:

Maternal body: 316L, brass

Upper cover: 316L, brass

Membrane: 316L

Filter screen: 316L (10 μ m)

Valve seat: PCTFE, PTFE, Vespel

Spring: 316L

Valve core ejector: 316L

三、進口乙炔鋼瓶減壓閥產品特征：

進口乙炔鋼瓶減壓閥，單級式膜片減壓結構，不銹鋼膜片壓力傳輸，輸出壓力穩定，適用于純凈氣體、標準氣體、腐蝕性氣體等。用用于石油化工、化纖、照明電器、熱處理、冶金、玻璃、食品、醫藥、電子、國防航天等主導領域。

德國洛克進口乙炔鋼瓶減壓閥接口可以適配國內所有規格的鋼瓶接口，特有的入口壓力補償技術抵消了因鋼瓶用氣后壓力下降導致的閥后壓力變動的問題。

Imported acetylene cylinder pressure reducing valve, single-stage diaphragm pressure reducing structure, stainless steel diaphragm pressure transmission, stable output pressure, suitable for pure gas, standard gas, corrosive gas, etc. It is used in petrochemical, chemical fiber, lighting appliances, heat treatment, metallurgy, glass, food, medicine, electronics, national defense and aerospace.

The pressure relief valve interface of acetylene cylinder imported from Germany Locke can adapt to all domestic cylinder interfaces. The unique inlet pressure compensation technology can offset the pressure change after the cylinder is used due to the pressure drop after the cylinder is used.

四、進口乙炔鋼瓶減壓閥產品簡介：

德國洛克-進口乙炔鋼瓶減壓閥，也叫乙炔鋼瓶減壓器，Acetylene cylinder reducing valve，就是將乙炔鋼瓶中的高壓氣體減為實驗及工況所需的低壓氣體壓力的減壓閥。采用活塞式減壓結構，輸出壓力穩定，主要用于石油化工、化纖、照明電器、熱處理、冶金、玻璃、食品、醫藥、電子、國防航天等主導領域的乙炔鋼瓶的出口減壓。

乙炔一般都是貯存在專用的高壓氣體鋼瓶中，使用時通過減壓閥使氣體壓力降至實驗所需范圍，再經過其它控制閥門細調，使氣體輸入使用系統。由于乙炔氣瓶內壓力較高，而氣焊和氣割和使用點所需的壓力卻較小，所以需要用減壓器來把乙炔儲存在氣瓶內的較高壓力的氣體降為低壓氣體，并應保證乙炔所需的工作壓力自始至終保持穩定狀態。進口乙炔減壓器是將高壓乙炔降為低壓氣體、并保持輸出乙炔的壓力和流量穩定不變的調節裝置。

Germany Locke imported acetylene cylinder pressure reducing valve, also known as acetylene cylinder reducing valve, is to reduce the high-pressure gas in acetylene cylinder to the low-pressure gas pressure required by experiments and working conditions. It is mainly used for export decompression of acetylene cylinders in petrochemical industry, chemical fiber, lighting appliances, heat treatment, metallurgy, glass, food, medicine, electronics, national defense and aerospace.

Acetylene is generally stored in a special high-pressure gas cylinder. When used, the gas pressure is reduced to the required range through the pressure reducing valve, and then the gas is input into the use system through other control valves. Due to the high pressure in acetylene cylinder, while the pressure required for gas welding, gas cutting and use point is relatively small, it is necessary to use a pressure reducer to reduce the high pressure gas stored in acetylene cylinder into low pressure gas, and ensure that the working pressure required by acetylene is stable from beginning to end. The imported acetylene pressure reducer is a regulating device which can reduce high pressure acetylene to low pressure gas and keep the pressure and flow rate of acetylene output stable.