進口球型止回閥德國洛克質量優異 價格美麗 

一、進口球型止回閥描述：

德國LOCKE洛克進口球型止回閥都是采用橡膠包皮球?yàn)殚y瓣，他們的原理是在介質的作用下，可在閥體內的滑道上前后滾動，從而起到打開或關閉閥門。單球型止回閥跟雙球形止回閥主要特點是流量大，流阻壓力損失小，密封性能好，消聲關閉，可減小水擊波。水平或垂直安裝均可。球形止回閥可用于冷水、熱水、工業及生活污水等管網的水泵出口，防止介質倒流。

The imported ball check valves of Locke lock in Germany are all made of rubber coated balls. Their principle is that under the action of medium, they can roll back and forth on the slide way in the valve body, so as to open or close the valve. Single ball check valve and double ball check valve are characterized by large flow rate, small flow resistance pressure loss, good sealing performance, silencing and closing, which can reduce water hammer wave. It can be installed horizontally or vertically. The ball check valve can be used at the outlet of water pump of cold water, hot water, industrial and domestic sewage pipe network to prevent the backflow of medium.

二、進口球型止回閥結構特點：

1、使用壽命長、可靠性高

2、動作靈敏、密封性能好

3、流道通暢、流體阻力小

4、閥瓣行程短、關閥沖擊力小

5、閥瓣關閉快速，水錘壓力小

6、水平或垂直管道均可使用，安裝方便

7、整體結構、簡單緊湊、造型美觀

8、結構長度短，其結構長度只有傳統法蘭止回閥的1/4~1/8

9、體積小、重量輕、其重量只有傳統微阻緩閉止回閥的1/4~1/20

1. Long service life and high reliability

2. Sensitive movement and good sealing performance

3. Smooth flow passage and small fluid resistance

4. Short disc travel and small valve closing impact

5. The valve disc is closed quickly and the water hammer pressure is small

6. Horizontal or vertical pipes can be used, easy to install

7. Overall structure, simple and compact, beautiful shape

8. The structure length is short, and its structure length is only 1 / 4 ~ 1 / 8 of the traditional flange check valve

9. Small volume, light weight, its weight is only 1 / 4 ~ 1 / 20 of the traditional micro resistance slow closing check valve

三、進口球型止回閥技術參數：

1、公稱壓力：1.0～1.6MPa

2、公稱通經：40～600mm

3、適用介質：水及弱腐蝕性流體

4、適用溫度：0～80℃

5、閥體：鑄鐵、不銹鋼等

6、閥蓋：鑄鐵、鑄鋼

7、球體：碳鋼+丁腈橡膠

8、閥座：碳鋼、不銹鋼

1. Nominal pressure: 1.0 ～ 1.6Mpa

2. Nominal diameter: 40-600mm

3. Applicable medium: water and weak corrosive fluid

4. Applicable temperature: 0 ～ 80 ℃

5. Valve body: cast iron, stainless steel, etc

6. Valve cover: cast iron, cast steel

7. Sphere: carbon steel + NBR

8. Valve seat: carbon steel, stainless steel