進口彈簧全啟式安全閥外觀精美質量耐用德國洛克

一、進口彈簧全啟式安全閥技術參數：

1、公稱通徑：DN15-DN400

2、工作壓力：1.6Mpa-42.0 Mpa。

3、工作溫度：-20℃+550℃。

4、驅動方式：手動、自動。

5、連接方式：螺紋、法蘭、焊接。

6、制造標準：國標GB、JB、HG，美標API、ANSI，英標BS，日本JIS、JPI等。

7、閥體材質：銅、鑄鋼、碳鋼、WCB、不銹鋼、304、304L、316、316L等。

1. Nominal diameter: dn15-dn400

2. Working pressure: 1.6mpa-42.0mpa.

3. Working temperature: - 20 ℃ + 550 ℃.

4. Driving mode: manual and automatic.

5. Connection method: thread, flange, welding.

6. Manufacturing standards: GB, JB, Hg, API, ANSI, BS, JIS, JPI, etc.

7. Valve body material: copper, cast steel, carbon steel, WCB, stainless steel, 304, 304L, 316, 316L, etc.

二、進口彈簧全啟式安全閥描述：

德國《LOCKE》洛克進口彈簧全啟式安全閥適用于工作溫度≤350℃的蒸汽、水等介質的設備和管路上。作為超壓保護裝置。是一種安全保護用閥，它的啟閉件受外力作用下處于常閉狀態，當設備或管道內的介質壓力升高，超過規定值時自動開啟，通過向系統外排放介質來防止管道或設備內介質壓力超過規定數值。

Locke spring full open safety valve is suitable for steam, water and other medium equipment and pipeline with working temperature ≤ 350 ℃. As overpressure protection device. It is a valve for safety protection. Its opening and closing parts are normally closed under the action of external force. When the medium pressure in the equipment or pipeline increases, it will automatically open when it exceeds the specified value. By discharging medium outside the system, the medium pressure in the pipeline or equipment will be prevented from exceeding the specified value.

三、進口彈簧全啟式安全閥操作方法：

①安全閥出廠前，應逐臺調整其開啟壓力到用戶要求的整定值。若用戶提出彈簧工作壓力級，則按 一般應按壓力級的下限值調整出廠。

②使用者在將安全閥安裝到被保護設備上之前或者在安裝之前，必須在安裝現場重新進行調整，以 確保安全閥的整定壓力值符合要求。

③在注明的彈簧工作壓力級范圍內，通過旋轉調整螺桿改變彈簧壓縮量，即可對開啟壓力進行調節 。

④在旋轉調整螺桿之前，應使閥進口壓力降低到開啟壓力的 90%以下，以防止旋轉調整螺桿時閥瓣 被帶動旋轉，以致?lián)p傷密封面。

① Before leaving the factory, the opening pressure of the safety valve shall be adjusted one by one to the setting value required by the user. If the user puts forward the spring working pressure level, it should be adjusted according to the lower limit of the pressure level.

② Before installing the safety valve on the protected equipment or before installation, the user must readjust it at the installation site to ensure that the set pressure value of the safety valve meets the requirements.

③ Within the indicated working pressure range of spring, the opening pressure can be adjusted by rotating the adjusting screw to change the compression amount of spring.

④ Before rotating the adjusting screw, the inlet pressure of the valve shall be reduced below 90% of the opening pressure to prevent the valve disc from being driven to rotate when rotating the adjusting screw, so as to damage the sealing surface.

四、進口彈簧全啟式安全閥選型：

1、根據彈簧全啟式安全閥操作壓力選擇合適公稱壓力；

2、根據彈簧全啟式安全閥操作溫度選擇合適使用溫度范圍；

3、根據計算出的彈簧全啟式安全閥的定壓值決定彈簧或杠桿的定壓范圍；

4、根據使用介質選擇合適彈簧全啟式安全閥的材質和結構型式；

5、根據彈簧全啟式安全閥泄放量選擇合適的喉徑。

1. Select the appropriate nominal pressure according to the operating pressure of spring full open safety valve;

2. According to the operating temperature of spring full open safety valve, select the appropriate temperature range;

3. The constant pressure range of the spring or lever is determined according to the calculated constant pressure value of the spring full open safety valve;

4. Select the material and structure of the spring full open safety valve according to the medium used;

5. Select the appropriate throat diameter according to the discharge capacity of spring full open safety valve.