進口常開式氣動隔膜閥歐美品牌德國洛克

 

進口常開式氣動隔膜閥結構特點:

①氣動閥門的反饋信號采用無觸點傳感技術；

②當氣源發生故障時，可操作手輪使閥門開啟或關閉；

③采用薄膜式氣缸替代活塞式氣缸，排除了活塞環易損漏而導致無法啟閉閥門的弊端；

④氣動隔膜閥門可附裝反饋信號、限位器和定位器，以適應自控、程控或調節流量的需要。

                                                                                 

進口常開式氣動隔膜閥規格參數：

口徑范圍:DN15 ~DN300

壓力范圍:PN6-16

溫度范圍:-40℃~180℃

傳動方式:手動

閥體：鑄鐵、球墨鑄鐵、碳鋼、不銹鋼

閥蓋：鑄鐵、球墨鑄鐵、碳鋼、不銹鋼

襯里：無襯里、橡膠

隔膜：橡膠

閥瓣：鑄鐵、碳鋼

氣缸：球墨鑄鐵

活塞：碳鋼

閥桿：碳鋼

手輪：鑄鐵

 

進口常開式氣動隔膜閥簡介：

德國洛克 《DE LOCKE 》進口常開式氣動隔膜閥，不通氣源時，閥體為常開狀態，通氣后關。該氣動常開式襯氟隔膜閥專用于控制非腐蝕性或強腐蝕性介質，閥體內腔表面無襯里或覆有可供選擇的各種襯氟塑料，適用于不同工作溫度和流體管路。

Introduction of imported normally open pneumatic diaphragm valve:
German Locke "de Locke" imports normally open pneumatic diaphragm valve. When the air source is not available, the valve body is normally open and closed after ventilation. The pneumatic normally open fluorine lined diaphragm valve is specially used to control non corrosive or strongly corrosive media. The surface of the inner cavity of the valve body is unlined or covered with various fluorine lined plastics for selection. It is suitable for different working temperatures and fluid pipelines.
                                                                                    

進口常開式氣動隔膜閥維護保養和安裝使用注意事項:

1. 隔膜閥應存放在干燥通風的室內，嚴禁堆迭放置。

2. 庫存隔膜閥的通路兩端必須封口，以防止異物進入內腔而損傷密封部件，且應避免與油類物品接觸。

3. 隔膜閥的金屬加工表面應清除污垢，并涂以防銹油。油杯內需經常注以潤滑油脂。

4. 襯膠層或橡膠隔膜表面切勿涂刷油脂類物品，以免產生橡膠溶脹而影響閥門使用壽命。

5. 在存放期間或停用期間，應逆時針旋轉手輪，使閥門處于微啟狀態，避免使隔膜因長期受壓而失去彈性。

6. 運輸過程中或安裝時，吊索不得系結在手輪或閥桿上。并嚴禁與其他金屬或硬質物件撞擊，以防止損傷零件和襯膠。

7. 安裝前，應仔細核對管路的運行條件及介質是否與本閥的適用范圍相符，避免選用不當而造成不必要的損失，乃至發生意外事故。

8. 除不宜應用于真空管路上，可在管路的任意位置安裝作雙向流動，但應確保操作和維修的方便。

9. 安裝前，應將閥體內腔清洗干凈，防止污垢卡阻或損傷密封部件，氣動隔膜閥價格，并檢查各部件連接螺栓是否均布緊固。

10. 運行中必須經常檢查與介質接觸的部件，并按實際使用情況，定期更換易損部件。

11. 當更換隔膜時，應注意切勿將隔膜擰得過緊或過松。

12. 應用于間斷性運行管路上，氣動隔膜閥銷售，則在停止使用期間，應清洗與介質接觸部位，以延長使用壽命。

Precautions for maintenance, installation and use of imported normally open pneumatic diaphragm valve:
1. The diaphragm valve shall be stored in a dry and ventilated room, and stacking is strictly prohibited.
2. Both ends of the channel of the diaphragm valve must be sealed to prevent foreign matters from entering the inner cavity and damaging the sealing parts, and avoid contacting with oil.
3. The metal working surface of diaphragm valve shall be cleaned of dirt and coated with antirust oil. The oil cup should be filled with lubricating grease frequently.
4. Do not brush grease on the rubber lining or rubber diaphragm surface to avoid rubber swelling and affecting the service life of the valve.
5. During storage or out of service, turn the hand wheel counterclockwise to make the valve slightly open to avoid the diaphragm losing its elasticity due to long-term pressure.
6. The sling shall not be tied to the hand wheel or valve stem during transportation or installation. It is strictly forbidden to collide with other metal or hard objects to prevent damage to parts and rubber lining.
7. Before installation, carefully check whether the operation conditions and medium of the pipeline are consistent with the scope of application of the valve, so as to avoid unnecessary losses and accidents caused by improper selection.
8. Except that it is not suitable for vacuum pipeline, it can be installed at any position of the pipeline for two-way flow, but the convenience of operation and maintenance should be ensured.
9. Before installation, the inner cavity of the valve body should be cleaned to prevent dirt from blocking or damaging the sealing parts. The price of the pneumatic diaphragm valve should be reduced, and the connecting bolts of all parts should be checked to see if they are evenly distributed and fastened.
10. During the operation, the parts contacting with the medium must be checked frequently, and the vulnerable parts must be replaced regularly according to the actual use.
11. When replacing the diaphragm, pay attention not to screw the diaphragm too tight or too loose.
12. When it is applied to the pipeline with intermittent operation and the pneumatic diaphragm valve is sold, the parts in contact with the medium should be cleaned to extend the service life.