進口高壓減壓閥德國洛克廠家直銷  

進口高壓減壓閥結構特點：

◆結構新穎合理、高壓減壓穩定

◆工作平穩可靠、大流量通行

◆閥瓣快開慢閉、高壓差時無水錘沖擊(關閉時間可調)

◆減穩壓精度高、調節范圍大

◆密封性能好、使用壽命時間長

進口高壓減壓閥規格參數：

◆產品規格：DN15-DN350

◆閥體材質：鑄鐵,鑄鋼,不銹鋼等

◆適用介質：氣體、水、油、蒸汽、腐蝕流體等

◆溫度范圍：-20℃≈550℃

◆壓力范圍：1.6~16Mpa

◆連接方式：法蘭,螺紋,焊接

◆結構形式：先導活塞式、薄膜式

◆適用范圍：水、油品、排渣、食品、污水、沉淀池及某些腐蝕性液體。

進口高壓減壓閥的選用： 

進口高壓氣體減壓閥的根據使用要求選定減壓閥的類型和調壓精度，再根據所需*輸出流量選擇其通徑。決定閥的氣源壓力時，應使其大于最輸出壓力0．1MPa。減壓閥一般安裝在分水濾氣器之后，油霧器或定值器之前，并注意不要將其進、出口接反；閥不用時應把旋鈕放松，以免膜片經常受壓變形而影響其性能。

Selection of imported high pressure reducing valve:
The type and pressure regulating precision of the imported high pressure gas pressure reducing valve are selected according to the use requirements, and then the diameter is selected according to the required maximum output flow. When determining the air source pressure of the valve, it should be greater than the maximum output pressure of 0.1MPa. The pressure reducing valve is generally installed after the water separating air filter and before the oil mist filter or the setting device, and the inlet and outlet of the pressure reducing valve should not be connected reversely; when the valve is not in use, the knob should be relaxed to avoid the diaphragm often being compressed and deformed to affect its performance.
 

進口高壓減壓閥產品安裝說明：

1、安裝高壓減壓閥之前必須對管路系統進地沖洗清理，以防焊渣、氧化皮等臟物流入閥內，影響閥門正常工作。

2、高壓氣體減壓閥應安裝在便于操作和維修的地方，并且必須直立安裝在水平管路上(見安裝示意圖)應注意使管路中介質的流向與閥體上箭頭所示方向一致，切勿裝反.

3、高壓氣體減壓閥在安裝使用時，應先把旁通管路上的截止閥打開，排除管路中的冷凝水和汽水混合物，以防減壓閥開啟時產生水擊現象損壞減壓閥，當無異?，F(xiàn)象后，按順時針方向緩慢旋轉調節螺釘，將出口壓力調至所需要的壓力(以閥后表壓為準)，調整好后，將鎖緊螺母鎖緊，擰上防護罩。

4、減壓閥前應安裝過濾器，以防止介質中的雜質進入減壓閥，影響其性能。

5、安裝的減壓閥前后應有一段直管，閥前直管長度約為600毫米，閥后直管長度約為1000毫米。

Installation instructions for imported high pressure relief valve products:
1. Before installing the high-pressure pressure reducing valve, the pipeline system must be flushed and cleaned to prevent welding slag, oxide scale and other dirt from flowing into the valve and affecting the normal operation of the valve.
2. The high-pressure gas pressure reducing valve should be installed in a place convenient for operation and maintenance, and it must be installed vertically on the horizontal pipeline (see the installation diagram). Attention should be paid to make the flow direction of medium in the pipeline consistent with the direction indicated by the arrow on the valve body, and do not install it reversely
3. When the high pressure gas pressure reducing valve is installed and used, the stop valve on the bypass pipeline should be opened first to remove the condensate water and steam water mixture in the pipeline, so as to prevent water hammer from damaging the pressure reducing valve when the pressure reducing valve is opened. When there is no abnormal phenomenon, slowly rotate the adjusting screw clockwise to adjust the outlet pressure to the required pressure (based on the gauge pressure behind the valve). After the adjustment, the outlet pressure should be adjusted, Lock the lock nut and screw on the protective cover.
4. A filter should be installed before the pressure reducing valve to prevent impurities in the medium from entering the pressure reducing valve and affecting its performance.
5. There should be a straight pipe before and after the pressure reducing valve. The length of the straight pipe in front of the valve is about 600mm, and the length of the straight pipe behind the valve is about 1000mm.