整個防護墻鋼模具組裝完成后內里要涂刷上適量的脫模劑，泥漿選取水泥或者是混凝土澆筑在模具中，等待泥漿成型后才可以進行拆模。注入上泥漿后插入振動棒進行振搗將氣泡排出去后，防撞墻凝固了表面才會更加的光滑，如果防撞墻在成型后表面會有不同大小的氣孔，就會直接的影響到成批防撞墻的合格率，而且也會導致模具的使用出現一些損壞的問題。泥漿凝固后拆模時要將螺栓取下來，自然這樣就可以讓防護墻鋼模具更快的進行拆模了，而且拆開后的模板要使用刷子進行清理，如果說有泥漿粘附在模板表面的話，就會影響到下次的使用防撞墻的作用就是在出現交通事故時，車輛會出下撞擊的問題，而防撞墻可以削減車輛的沖擊力度，減少車輛的受損問題。防撞墻大部分都是用到了混凝土來進行澆筑，并且也可以根據要求在模具內放置上編織好的鐵絲網，可以有效的增強防撞墻的抗撞擊能力。在生產的時候由于防護墻鋼模具是前后通透的，而模具的頂部是有著拉桿可以調節尺寸，因此使用方便可以放心來進行加工施工處理。如需使用防撞墻模具的話就要將整個模具在需要施工的位置進行擺放，調整好模具的尺寸以及施工角度，之后將模具固定好后前后進行隔斷，內里刷油后來進行泥漿的注入就可以了。After the assembly of the steel mould for the whole protective wall, a proper amount of release agent should be applied inside. Cement or concrete should be selected for slurry pouring in the mould, and the mould can be removed after the slurry is formed. After injecting the slurry, insert the vibrator to vibrate and discharge the bubbles, the surface of the anti-collision wall will be smoother after solidification. If there are different sizes of pores on the surface of the anti-collision wall after forming, it will directly affect the qualification rate of the batch of anti-collision walls, and also lead to some damage problems in the use of the mold. After the slurry solidifies, the bolts should be removed when removing the formwork. Naturally, the formwork of the protective wall can be removed more quickly. Moreover, the removed formwork should be cleaned with a brush. If the slurry adheres to the surface of the formwork, the next use will be affected.

The function of the anti-collision wall is that when there is a traffic accident, the vehicle will crash, and the anti-collision wall can reduce the impact of the vehicle and reduce the damage of the vehicle. Most of the anti-collision walls are poured with concrete, and the woven wire mesh can be placed in the mold according to the requirements, which can effectively enhance the anti-collision ability of the anti-collision wall. In production, because the protective wall steel mold is transparent in front and back, and the top of the mold has a pull rod to adjust the size, so it is easy to use and can be safely processed. If it is necessary to use the anti-collision wall mold, the whole mold should be placed at the position where it needs to be constructed, and the mold size and construction angle should be adjusted. After that, the mold should be fixed, and then the front and back should be cut off, and the inside should be oiled, and then the mud should be injected.