躍泰達科技
主營產品: 貼片保險絲, 自恢復保險絲, 薄膜電容, 溫控開關, 熱敏電阻, 一次性保險絲
成都方形保險絲125mA/350V
價格
訂貨量(PCS)
¥0.12
≥200
店鋪主推品 熱銷潛力款
憩憭憦憬憤憬憦憤憭憤憧
躍泰達科技
店齡6年 企業認證
聯系人
付先生 經理
聯系電話
憩憭憦憬憤憬憦憤憭憤憧
經營模式
生產廠家
所在地區
廣東省深圳市
主營產品
貼片保險絲, 自恢復保險絲, 薄膜電容, 溫控開關, 熱敏電阻, 一次性保險絲
外觀Appearance
外觀不應有顯著的污點、裂紋。
There shall not be any remarkable stain,rust or crack on the appearances.
標示應該很容易辨識。
Marking shall be easily legible.
機械特性Mechanical characteristics
拉力強度試驗Tensile test
將保險絲固定好后,對保險絲引線施加5N的拉力,持續1分鐘。試驗過后,保險絲沒有任何破損現象。
Exert the axial pulling force of 5N to the both ends of lead wire for 1 minute. After the test the fuse shall be no damage and loosening.
電氣特性Electrical characteristics
實驗條件Test condition
所有測試環境溫度為25±5℃。
All electrical characteristics tests are conducted at an ambient temperature of 25±5℃.
分?jǐn)嗄芰?/font>Interrupting rating test
保險絲能承受的分?jǐn)嗄芰?/font>:35A或10倍的額定電流當中較大的。分?jǐn)嗄芰y(cè)試后測得保險
絲的絕緣阻抗值大于0.1ΜΩ。
The fuse interrupting capacity:35A or 10 times the rated current whichever is greater. After
interrupting, the insulation resistance between the fuse terminations shall be not less than 0.1ΜΩ.
3溫度上升試驗:通1.5倍額定電流15分鐘,然后每隔15分鐘增加0.1倍額定電流。測得保
險絲斷開時任何部位的溫升不得超過135℃,周?chē)h(huán)境溫度為25±5℃。
Temperature Rising Test: The rated current of 1.5 times is applied for 15 minutes. After the first
15minutes, the current is increased by 0.1 times the rated current every 15 minutes until the fuse
operates. The temperature rising on the fuse surface is not higher than 135℃.
額定電流的% % of ampere rating | 熔斷時間 Opening time |
210% | 2 min Max |
275% | 400 ms~10 s |
400% | 150 ms~3 s |
1000% | 20 ms~150 ms |
耐久性測試 Endurance test
對保險絲通過相關標準規格單規定的額定電流1小時,然后截?cái)嚯娏?/font>15分鐘,將該循環重復
100次。試驗過后保險絲沒有任何破損現象。
A ampere rating specified in the relevant standard sheet is passed through the fuse for a period of
1h.The current is then switched off for a period of 15 minutes. This cycle is repeated 100 times. After
the test the fuse shall be no damage and loosening.
焊接參數 Soldering parameters
波峰焊 260℃,最大10秒,
Wave soldering 260 ℃,10 sec. Maximum
手工焊 370℃,最大5秒,
Manual soldering 370℃, 3 sec. Maximum
時間電流曲線圖見附頁 Time- current curve see attachment
環境特性Environmental characteristics
使用溫度范圍 Operating Temperature
-55℃~125℃。
保存條件Storage Conditions
相對濕度≦75%,可存放3年。
Relative humidity ≦ 75%, store 3 years .