進口低溫液氮止回閥選德國洛克專業生產質量放心 

一、進口低溫液氮止回閥規格參數：

Specification range: DN 10-dn200

Temperature range - 196 ℃～ 150 ℃

Pressure range: pn1.6 ~ pn10mpa

Valve body material: special low temperature steel

Valve cover material: special low temperature steel

The valve seat and core are forged with low temperature steel and PTFE

Application range: liquid nitrogen and industrial low temperature liquid.

Connection mode: German standard / national standard / American Standard, flange, welding, internal thread

Applicable medium: liquid natural gas, hexene, carbon dioxide, liquid ammonia, liquid oxygen, liquid nitrogen, liquid hydrogen and other low-temperature media

Applications: gas liquefaction equipment, air separation equipment; natural gas liquefaction, storage and transportation equipment; low temperature storage tanks and tank cars for liquid oxygen, nitrogen, argon, hydrogen and carbon dioxide; pressure swing adsorption oxygen and nitrogen production equipment.

二、進口低溫液氮止回閥產品簡介：

德國LOCKE洛克進口低溫液氮止回閥又稱低溫逆止閥、低溫單向閥、低溫逆流閥、和低溫背壓閥，是指采用經過低溫深冷的不銹鋼材質，在低溫貯槽上或者低溫管道系統，依靠介質本身流動而自動開、閉閥瓣，防止低溫介質液氧，液氮，液氬，液化天然氣，LO2、LN2、LAR、LNG等倒流的閥門，

 LOCKE低溫液氮止回閥結構緊湊、體積小、重量輕，防止倒流零泄露，穩定性好。

液氮（常寫為LN2），是氮?dú)庠诘蜏叵滦纬傻囊后w形態。氮的沸點為-196°C，在正常大氣壓下溫度如果在這以下就會形成液氮；在工業中，液態氮是由空氣分餾而得。先將空氣凈化后，在加壓、冷卻的環境下液化，借由空氣中各組分之沸點不同加以分離。氦氣最先泄出(且未被液化)，接著就是占空氣中78.09%的氮?dú)猓賮?lái)是占20.95%的氧氣，最后是占空氣中0.93%的氬氣。

Low temperature liquid nitrogen check valve imported from Germany Locke, also known as low-temperature check valve, low-temperature check valve, low-temperature reverse flow valve and low-temperature back-pressure valve, refers to the use of low-temperature cryogenic stainless steel material, in the low-temperature storage tank or low-temperature pipeline system, depending on the flow of the medium itself to automatically open and close the valve disc, to prevent low-temperature medium, liquid oxygen, liquid nitrogen, liquid argon, liquefied natural gas, LO2, LN2, La R. LNG and other reverse flow valves,

Lock low temperature liquid nitrogen check valve has the advantages of compact structure, small volume, light weight, preventing backflow, zero leakage and good stability.

Liquid nitrogen (usually written as LN2) is the liquid form of nitrogen formed at low temperature. The boiling point of nitrogen is - 196 ° C. under normal atmospheric pressure, if the temperature is below this, liquid nitrogen will be formed; in industry, liquid nitrogen is obtained by fractional distillation of air. The air is first purified and then liquefied in a pressurized and cooled environment, and separated by the different boiling points of each component in the air. Helium was first released (and not liquefied), followed by nitrogen (78.09%), oxygen (20.95%), and argon (0.93%).

三、進口低溫液氮止回閥安裝與維護：

1,本閥門通路兩端須堵塞，存在干燥通風的室內。如長期存放，應經常檢查防銹蝕。

2,安裝前應將閥門清洗干凈，并消除在運輸過程中造成的缺陷。

3,安裝時必須仔細核對閥門上的標志和銘牌是否符合使用要求。

4,升降式垂直瓣止回閥應安裝在垂直管道上。

5,升降式水平瓣止回閥應安裝在水平管道上。

6,在管線中不要使止回閥承受重量，大型的止回閥應獨立支撐，使之不受管系產生的壓力的影響。

7,安裝止回閥時，應特別注意介質流動方向，應使介質正常流動方向與閥體上指示的箭頭方向相一致，否則就會截?cái)嘟橘|(zhì)的正常流動。底閥應安裝在水泵吸水管路的底端。

8,通式升降式止回閥應安裝于水平管路上,立式升降式止回閥和底閥一般安裝在垂直管路上,并且介質自下而上流動。

9,止回閥關閉時，會在管路中產生水錘壓力，嚴重時會導致閥門、管路或設備的損壞，尤其對于大口管路或高壓管路，故應引起止回閥選用者的高度注意。

1. Both ends of the valve passage must be blocked, and there is a dry and ventilated room. If it is stored for a long time, it should be checked for rust.

2. The valve should be cleaned before installation, and the defects caused during transportation should be eliminated.

3. Carefully check whether the signs and nameplates on the valve meet the use requirements during installation.

4. Lift type vertical disc check valve shall be installed on vertical pipe.

5. Lift type horizontal disc check valve shall be installed on horizontal pipeline.

6. Do not make the check valve bear the weight in the pipeline. The large check valve should be independently supported to prevent it from being affected by the pressure generated by the pipeline system.

7. When installing the check valve, special attention should be paid to the flow direction of the medium. The normal flow direction of the medium should be consistent with the arrow direction indicated on the valve body, otherwise the normal flow of the medium will be cut off. The bottom valve should be installed at the bottom of the water pump suction pipe.

8. The general lifting check valve shall be installed on the horizontal pipeline, while the vertical lifting check valve and bottom valve are generally installed on the vertical pipeline, and the medium flows from bottom to top.

9. When the check valve is closed, there will be water hammer pressure in the pipeline, which will cause damage to the valve, pipeline or equipment in serious cases, especially for the large opening pipeline or high pressure pipeline, so it should be paid great attention by the check valve selector.

四、進口低溫液氮止回閥結構特點：

1、經過低溫深冷處理，能耐-196℃低溫

2、閥瓣材料經過鍍鉻或氮化處理，提高閥桿表面硬度，提高填料密封的可靠性。

3、用的墊片具有在常溫下、低溫狀態及溫度變化下能可靠密封性和復原性。

4、采用優質的德國LOCKE洛克各種零部件材料，能達到流體逆向零泄露，防止倒流。

1. After cryogenic treatment, it can withstand - 196 ℃ low temperature

2. After chromium plating or nitriding treatment, the surface hardness of valve stem is improved and the reliability of packing seal is improved.

3. The gasket can be reliably sealed and recovered under normal temperature, low temperature and temperature change.

4. Using high quality German locke parts materials, it can achieve reverse zero leakage of fluid and prevent backflow.